manualshive.com logo in svg

BTECH S5 BATTERY VALIDATION SYSTEM SCM-600, Operating Manual

Share
Download
BTECH S5 BATTERY VALIDATION SYSTEM SCM-600 Operating Manual Download Page 12

12

S5 Battery Validation System

3. Installing Drivers for the USB Port on SCM-600

.

Steps to Install USB Drivers

Screen Shot

For WINDOWS XP Installation from CD

1

The drivers should be installed from the BVM Installation CD. If the CD is not 

available and the PC is connected to the Internet, the drivers can be installed via 

Windows Update.
Connect the USB port on the SCM-600 to a free USB port on the PC or hub 

connected to a USB port on the PC. This will bring up the Found New Hardware 

Wizard. Select “No, not this time” on the wizard and click the Next button.

2

If the BVM Installation CD is not inserted, insert it now. Select “Install from a list 

or specific location” and click the Next button.

3

Select “Search for the best driver in these locations” and make sure the “Search 

removable media (floppy, CD-ROM) is checked. Then click the Next button.

4

The wizard will search for and install the first driver for the USB port. Click the 

Next button when it is complete.

5

When the wizard finishing installing the driver, click the Finish button.

Summary of Contents for S5 BATTERY VALIDATION SYSTEM SCM-600



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands