BT LPE200 Service Manual Download Page 144 | Manualshive

Page: 144 / 154

background image

11- 2

Service Guide

LWE180, LWE200, LPE200, LPE240

© BT Europe AB

Hydraulic/Pneumatik – 6000 LWE 180/200 LPE 200

Adjustments LWE180

T-code

Valid from serial number

Date

Order number

660, 661, 662, 497

723984-

2005-05-11

225553-040

11.3 Adjustments LWE180

11.3.1 Adjusting the pressure limit valve

The pressure limit valve is set to the correct value at the factory, but
may need to be adjusted if the valve or the complete hydraulic unit is
replaced.

The truck should be capable of lifting a load of between 1850-1900 kg.

1.

Locking nut. Use special tool, see drawing in chapter “Tools”.

2.

Adjuster screw, pressure limit.

Adjusting clockwise results in increased pressure.

Adjusting anticlockwise results in decreased pressure.

3.

Pressure limit valve. Use special tool, see drawing in chapter
“Tools”.

•

Loosen the locking nut (1) using a special tool (see drawing 3.2).
Place a load of 1800 kg on the forks and check that the truck can lift
it.

•

If the truck lifts 1800 kg, place a further 100 kg on the forks. Check
whether the truck can lift the load.

•

If the truck lifts 1900 kg, adjust the pressure limit by turning the ad-
juster screw (2) anticlockwise using a 4 mm allen key until the truck
cannot lift the load.

1

2

3

«
...
142
143
144
145
146
...
»

Summary of Contents for LPE200



























































































































































Reviews:

No comments

Related manuals for LPE200

Brand: UniCarriers Pages: 161

Brand: Big Lift Pages: 24

Brand: Blue Giant Pages: 32

Brand: Blue Giant Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands