Bryant 935SA Manual Download

Page: 8 / 60

935SA: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Location Relative to Cooling Equipment

The cooling coil must be installed parallel with, or on the downstream

side of the unit to avoid condensation in the heat exchangers. When

installed parallel with the furnace, dampers or other flow control must

prevent chilled air from entering the furnace. If the dampers are

manually operated, they must be equipped with means to prevent

operation of either unit unless the damper is in the full-heat or full-cool

position. Refer to Installation of Evaporator Coil section for install

requirements for unshielded coils (

Table 6

AIR FOR COMBUSTION AND VENTILATION

Introduction

2-pipe Applications

When the furnace is installed as a 2-pipe furnace, no special provisions

for air for combustion are required. However, other gas appliances

installed in the space with the furnace may require outside air for

combustion. Follow the guidelines below to ensure that other gas

appliances have sufficient air for combustion.

1-pipe Applications

When the furnace is installed as a 1-pipe furnace, it will be necessary to

ensure there is adequate air for combustion. Other gas appliances

installed with the furnace may also require air for combustion and

ventilation in addition to the amount of combustion air and ventilation

air required for the furnace. Follow the guidelines below to ensure that

the furnace and other gas appliances have sufficient air for combustion.

Ventilated Combustion Air Applications (for U.S. Only)

When the furnace is installed using the ventilated combustion air option,

the attic or crawlspace must freely communicate with the outdoor to

provide sufficient air for combustion. The combustion air pipe cannot be

terminated in attics or crawlspaces that use ventilation fans designed to

operate during the heating season. If ventilation fans are present in these

areas, the combustion air pipe must terminate outdoors as a 2-Pipe

system.
All air for combustion is piped directly to the furnace from a space that is

well ventilated with outdoor air (such as an attic, crawl space or

equipment closet) and the space is well isolated from the living space or

garage. In addition, other gas appliances installed in the space with the

furnace may require outside air for combustion. Follow the guidelines

below to ensure that the roof or crawlspace walls have sufficient free

area to provide sufficient air for combustion and ventilation for the

furnaces. The guidelines below can be used to ensure that other gas

appliances have sufficient air for combustion.
Provisions for adequate combustion, ventilation, and dilution air must be

provided in accordance with:

• U.S.A. Installations: Current edition of Section 9.3 of the NFPA

54/ANSI Z223.1, Air for Combustion and Ventilation and applicable

provisions of the local building codes.

The requirements for combustion and ventilation air depend upon

whether or not the furnace is located in a space having a volume of at

least 50 cubic feet per 1,000 BTUh input rating for all gas appliances

installed in the space.

• Spaces having less than 50 cubic feet per 1,000 BTUh (4.8 cubic

meters per kW) require the Outdoor Combustion Air Method.

• Spaces having at least 50 cubic feet per 1,000 BTUh (4.8 cubic meters

per kW) may use the Indoor Combustion Air, Standard or Known Air

Infiltration Method.

Outdoor Combustion Air Method

1. Provide the space with sufficient air for proper combustion,

ventilation, and dilution of flue gases using permanent horizontal or

vertical duct(s) or opening(s) directly communicating with the

outdoors or spaces that freely communicate with the outdoors.

2. Provide TWO OUTDOOR OPENINGS, one inlet and one outlet

combustion and ventilation air opening, to the outdoors (see

Fig. 8

a. One opening MUST commence within 12 in. (300 mm) of the

ceiling and the second opening MUST commence within 12 in.

(300 mm) of the floor.

b. Size openings and ducts (see

Fig. 8

and

Table 3

c. TWO HORIZONTAL DUCTS require 1 sq. in. (645 sq. mm) of

free area per 2,000 BTUh (1,100 mm2/kW) of combined input

for all gas appliances in the space (see

Fig. 8

and

Table 3

d. TWO OPENINGS OR VERTICAL DUCTS require 1 sq. in.

(645 sq. mm) of free area per 4,000 BTUh (550 mm2/kW) for

combined input of all gas appliances in the space (see

Fig. 8

and

Table 3

3. ONE OUTDOOR OPENING requires:

a. 1 sq. in. (645 sq. mm) of free area per 3,000 BTUh (734

mm2/kW) for combined input of all gas appliances in the space

(see

Fig. 8

and

Table 3

b. Not less than the sum of the areas of all vent connectors in the

space.

The opening shall commence within 12 in. (300 mm) of the ceiling.

Appliances in the space shall have clearances of at least 1 in. (25 mm)

from the sides and back and 6 in. (150 mm) from the front. The opening

shall directly communicate with the outdoors or shall communicate

through a vertical or horizontal duct to the outdoors or spaces (crawl or

attic) that freely communicate with the outdoors.

WARNING

FIRE, INJURY OR DEATH HAZARD

Failure to follow this warning could result in personal injury, death

and/or property damage.

When the furnace is installed in a residential garage, the burners and

burner ignition devices must be located at least 18 in. (457 mm) above

the floor. The furnace must be located or protected to avoid damage by

vehicles. When the furnace is installed in a public garage, airplane

hangar, or other building having a hazardous atmosphere, the furnace

must be installed in accordance with the current edition of NFPA

54/ANSI Z223.1 or CAN/CSA B149.2 (see

Fig. 5

CAUTION

FURNACE CORROSION HAZARD

Failure to follow this caution may result in furnace damage.
Air for combustion must not be contaminated by halogen compounds,

which include fluoride, chloride, bromide, and iodide. These elements

can corrode heat exchangers and shorten furnace life. Air contaminants

are found in aerosol sprays, detergents, bleaches, cleaning solvents,

salts, air fresheners, and other household products.

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury or death.

The operation of exhaust fans, kitchen ventilation fans, clothes dryers,

attic exhaust fans or fireplaces could create a NEGATIVE PRESSURE

CONDITION at the furnace. Make-up air MUST be provided for the

ventilation devices, in addition to that required by the furnace. Refer to

the Carbon Monoxide Poisoning Hazard warning in the venting section

of these instructions to determine if an adequate amount of make-up air

is available.

Summary of Contents for 935SA





























































Search results

Summary of Contents for 935SA

Reviews:

Related manuals for 935SA

Brands by name

Popular brands

Bryant 935SA, Manual

Search results

Summary of Contents for 935SA

Reviews:

Related manuals for 935SA

Brands by name

Popular brands