Furniture Use and Maintenance
EN
§
Furniture Assembly
Explanations
/
Possible
notes
used
in
the
Assembly
Instructions:
§1
§2
§3
1.
2.
4.
5.
6.
7.
1. Furniture units must be placed on a level surface and levelled.
2.
Check the condition of the cam pins while the furniture is in use. Tighten if necessary.
4.
Furniture must be placed in dry rooms, with working ventilation, and at least 1 m from active heat sources. The rooms must be protected against
detrimental weather conditions (sunlight, rain, etc.).
6.
Furniture must be moved by being lifted it with no load on it. Note: shifting or dragging furniture may cause permanent damage. When moving,
hold the vertical elements of the unit, i.e. the sides and legs. Do not grab the horizontal elements, e.g. structural shelves or drawers, as these are
prone to damage.
7.
Clean furniture using a damp cloth or paper towel.
3. NOTE!! Do not climb on furniture.
5.NOTE!! Placing excessive loads on furniture is dangerous to users and may cause permanent damage.
§5
§6
§7
§8
§9
§4
Drill holes according to drawings. During this operation take
special care not to cut yourself or damage the component!
§10
§11
§12
§13
§14
§15
§18
§17
NOTE!!
Component symbol
Code
Pack
A
B
C
D
E
Dimensions [mm]
Quantity[pcs]
NOTE!!
NOTE!!
The first stage of the assembly involves fitting the components with
t
he proper accessories as specified on the drawings below.
The symbol
denotes places where special caution is required
during assembly.
NOTE!! L ack
o
for
improper
adjustment
poses
risk
of
flap
door
falling
freely.
Attach
unit
to
wall
when
completely
assembled.
Improperly
attached
furniture
may
break
free
and
fall
while
being
mounted
or
used.The
unit
may
only
be
attached
to
the
wall
by
a
qualified
person.
Check
that
the
wall
is
suitable
fo
rhaving
furniture
attached
to
it
before
hand.
Choose
a
suitable
anchor
bolt
and
check
the
strength
and
quality
of
the
attachment.
Place
the
top
unit
on
the
base
unit
then
join
them
using
connector
plate
n52
and
screws
p25.
The
unit
may
b
r
eak
free
and
fall
during
use
if
this
instruction
is
not
followed.
Assemble the unit according to the drawings below using the
specified connectors and/or joints.
ATTENTION!
The operation must be carried out very carefully
in order to damage the parts of the product.
Apply glue y1 into the holes of the depicted component, attach it and
wait for the glue to dry.
Clean the glued area thoroughly.
Adjustment
Tighten the screws e8 so they do not project over the rim.
Option
P
lace the insert upside down onto the frame in place designed for
that component using the unfolded top unit.
Use security tape as this is essential to ensure the safety of
those who use your furniture.
NOTE!!
Handle glass components with extra caution so as not to cut
yourself or damage or break the components.
Connect the adjoining units using VHS connecting screws.
§19
The door may be installed either on the left or the right side of the
unit.
§20
NOTE!! B ed unit and flap have a tendency to slam when
closing. There is a risk of injury.
§21
Apply masking strip/unit in visible places.
§22
2
A
B
A=B
4
f1
3
6
1
3.
5
n26
1
p38
x16 mm
§23
NOTE!!
High gloss fronts are covered with a protective film which
is to be removed once the component has been hung up.
The surface of these fronts cannot be cleaned until least 4 weeks
after removing the protective film.
NOTE!!
Furniture may break free and fall if not used with caution.
Note: Before starting to assemble furniture, please read all the Furniture Assembly Instructions including the rules for maintenance and use.
Follow the sequence of individual assembly stages according to the paragraphs provided in the General Rules for Furniture Assembly.
KEEP THESE INSTRUCTIONS FOR THE DURATION OF FURNITURE USE.
1.
NOTE!
Do not proceed with assembly if any components are defective or damaged.
2. Place the components on a soft, clean surface, e.g. a towel or blanket, during assembly. Do not assemble furniture on rags, carpets, etc.
3. Drive the dowel pins f1 into the 8mm diameter holes, located on components' edges. Leave the cam bolt holes free. Any pin that sticks out by more
than 10mm needs to be taken out, replaced and shortened as it may damage the side wall during assembly.
4. Make sure that the diagonals are of equal length before attaching the back wall.
5.
NOTE!
Safety strap. Install according to instructions. Improperly secured furniture may break free and fall during use.
6. Dear Customer, in case of complaints please quote the code number provided on the first page of the Assembly Instructions. Report all comments
and complaints where you purchased the furniture. If possible, provide a label of defective product indicating the packing date and the packer.
Set screw adjusts cabinet flap door opening (tighten the screw for
the
cabinet flap door to fall more freely).
Elements of accessories, designed for self-purchase in
specialized stores.
