manualshive.com logo in svg

Bruker NMR 400 89 Ascend DNP, User Manual, Page: 16 / 106

Share
Download
Bruker NMR 400 89 Ascend DNP User Manual Download Page 16

16

ZTKS0243 / Z31993 / 03

Safety

2.4

Residual Risks

In the following chapter the residual risks from the risk analysis according ISO 14971 are 
summarized. To prevent health hazards and hazardous situations obey all safety 
instructions and warnings in the manual.

2.4.1

Persons

2.4.2

Intended Use

The supplied magnet system is designed and intended for NMR spectroscopy only.

WARNING

Risk of injury and property damage due to handling by not approved 
persons.

Incorrect handling of the magnet system by not approved persons may result in 
significant bodily injury and property damage.
Thus:

• Work must only be carried out by approved persons with applicable qualifications. 

The necessary qualifications are specified in the beginning of the relevant 
chapter.

• In case of doubt, contact Bruker Service. Contact information see page 9 of this 

document.

WARNING

Risk of damage to life and limb by incorrect use of the magnet system.

Incorrect use of the magnet system can lead to life-threatening situations and 
destruction of the magnet system.
Thus:

• Only use the magnet system as intended.

• Do not change the magnet system.

• Do not exceed specified values for operating the magnet system.

• Do not use inserts inside the RT bore not approved by Bruker Service.

Damage claims from damages caused by other than the intended use of the magnet 
system are excluded and the customer is held liable.

Summary of Contents for NMR 400 89 Ascend DNP











































































































Reviews:

No comments