manualshive.com logo in svg

Bruker minispec mq20, User Manual, Page: 9 / 86

Share
Download
Bruker minispec mq20 User Manual Download Page 9

Safety

E1400912_1_001

9

2

Safety

This manual contains notices which should be observed to ensure your own personal safety
as well as to protect the spectrometer and the connected equipment.

2.1

Intended Use

The minispec mq20 Toothpaste Analyzer is a pulsed time-domain NMR analyzer used for the
monitoring of the fluorine nuclei.

This product is intended to be used solely for measurements on industrial samples.

2.2

Qualified Personnel

The  minispec  may  only  be  set  up  and  operated  in  conjunction  with  the  instructions  in  this
manual. Only qualified personnel should be allowed to work on this equipment. The primary
installation,  maintenance  and  repair  of  the  minispec  may  only  be  carried  out  by  personnel
which are authorized by BRUKER.

All repairs, adjustments and alignments performed on any components of the minispec must
be  carried  out  strictly  in  accordance  with  the  established  safety  practices  and  standards  of
the country where the instrument is installed.

2.3

Correct Usage

This  device  and  its  components  may  only  be  used  in  the  way  discussed  with  a  BRUKER
specialist  and  in  connection  with  devices  or  components  from  other  manufacturers  which
have been approved or recommended by BRUKER.

Note: This product can only function correctly and safely if it is transported, stored, set up
and installed correctly, and operated and maintained as recommended by BRUKER.

Summary of Contents for minispec mq20























































































Reviews:

No comments