manualshive.com logo in svg

Bruker minispec mq20, User Manual, Page: 69 / 86

Share
Download
Bruker minispec mq20 User Manual Download Page 69

minispec.exe Software for Diagnostic and Service Purposes

E1400912_1_001

69

Some of the functions described might only be available in certain minispec.exe software
versions.

8.3.8

The Process Menu

The 

Process

 item is only displayed when a Signal Window is active. Different commands for

data processing are summarized in this pull-down menu:

Figure 8.15: The Process Pull-Down Menu

Within the context not all commands may be reasonable, in which case they will be grayed.
The following series of built-in signal processing features are available:

The Fit Command

This  command  is  only  available  in  connection  with  calibrations.  You  can  fit  your  calibration
data and display the fit results (see 

Info Views

, point 4).

The FFT, Magnitude, Power and Absolute Commands

A Fast Fourier Transform of measurement data will be performed using the 

FFT

 command. If

the  NMR  signal  is  observed  in  complex  mode  (real  and  imaginary  part  of  the  signal)  the

Magnitude

  ([Re2+Im2]1/2)  or  the  power  spectrum  can  be  calculated.  From  the  real,

imaginary or complex data, the 

Absolute

 values can be calculated.

The Signal Flip, and the Signal Swap Command

The  signal  can  be  mirrored  with  respect  to  an  offset  frequency  of  0  using  the 

Signal  Flip

command. The 

Signal Swap

 command exchanges the real and imaginary part.

Summary of Contents for minispec mq20























































































Reviews:

No comments