manualshive.com logo in svg

Bruker minispec mq20, User Manual, Page: 60 / 86

Share
Download
Bruker minispec mq20 User Manual Download Page 60

minispec.exe Software for Diagnostic and Service Purposes

60

E1400912_1_001

The Licenses Command

Some special applications, like the digital pulse attenuation and the pulse shaping need to be
licensed.  Use  this  menu  to  open  the  license  number  input  box,  which  prompts  the  user  to
input  the  license  number.  After  a  successful  license  procedure,  the  menu  entry  is  checked
and grayed.

Have  ready  the  minispec  instrument's  system  number  (see  Status  Bar  )  and  contact
BRUKER for information or license numbers.

8.3.5

The Measurement Menu

All commands concerning the execution of measurements are concentrated in this menu item
(see the figure below). Since these commands are used frequently, quick select buttons are
available in the Measurement Tool Bar and key short cuts exist to enhance accessibility.

Figure 8.9: The Measurement Pull-Down Menu

The Run, Stop and Continue Commands

The 

Run

 command starts a measurement. If the Sample Detector is set 

ON

 (see: Instrument

Settings Command) the measurement will be executed automatically with the insertion of the
sample.

Shortcuts: Standard Tool Bar:

Measurement Tool Bar:

Keys: ALT+M or ENTER

To interrupt a minispec measurement, use the 

Stop

 command.

Shortcuts: Standard Tool Bar:

Measurement Tool Bar:

Summary of Contents for minispec mq20























































































Reviews:

No comments