BRUEL & KJAER PULSE 7788 Technical Documentation Manual Download Page 47

Page: 47 / 62

CHAPTER

Troubleshooting

Fig.7.2

Remote

Station

client

showing

connection

settings

2) Check to see if the IP addresses for the Vehicle and Ground Stations are both within

the correct family of IP addresses.

Note:

The Subnet mask must be set to

255.255.255.X

A Subnet mask

255.255.0.0

will

not

work!

7.5

Troubleshooting

the

Weather

Station

The weather station is a plug and play design utilizing Power over Ethernet (PoE) for a

single-cable installation.
If it is not functioning or functioning incorrectly, try to isolate the problem in the

following manner:

Are

there

values

visible

the

Ground

Station

PC?

If there are values present and they are incorrect, then check that the orientation of the

weather station is correct. There is an arrow underneath the body of the sensor that

points north, this must be aligned with true north unless otherwise configured in the

unit’s software.

Summary of Contents for PULSE 7788































































Search results

Summary of Contents for PULSE 7788

Reviews:

Related manuals for PULSE 7788

Brands by name

Popular brands

BRUEL & KJAER PULSE 7788, Technical Documentation Manual

Search results

Summary of Contents for PULSE 7788

Reviews:

Related manuals for PULSE 7788

Brands by name

Popular brands