BRP EVINDURE ICON II Instructions Manual Download Page 1

INSTRUCTIONS
 

Outboard Engines

356593

Printed in the United States.
© 2014 BRP US Inc. All rights reserved.
TM, ® and the BRP logo are registered trademarks of Bombardier Recreational Products Inc. or its affiliates.

1 of 6

EVINRUDE

®

 ICON II MODE & RPM SWITCH KIT - P/N 766282

SAFETY INFORMATION

The following symbols and/or signal words may
be used in this document:

These safety alert signal words mean:

ATTENTION!

BECOME ALERT!

YOUR SAFETY IS INVOLVED!

For safety reasons, this kit must be installed by
an authorized 

Evinrude

 dealer. This instruction

sheet is not a substitute for work experience. Ad-
ditional helpful information may be found in other
service literature.

DO NOT perform any work until you have read
and understood these instructions completely.

Torque wrench tightening specifications must
strictly be adhered to.

Should removal of any locking fastener (lock
tabs, locknuts, or patch screws) be required, al-
ways replace with a new one.

When replacement parts are required, use 

Evin-

rude/Johnson

®

 Genuine Parts

 or parts with

equivalent characteristics, including type,
strength and material. Use of substandard parts
could result in injury or product malfunction.

Always wear EYE PROTECTION AND APPRO-
PRIATE GLOVES when using power tools.

Unless otherwise specified, engine must be OFF
(not running) when performing this work.

Always be aware of parts that can move, such as
flywheels, propellers, etc.

Some components may be HOT. Always wait for
engine to cool down before performing work.

If you use procedures or service tools that are
not recommended in this instruction sheet, YOU
ALONE must decide if your actions might injure
people or damage the outboard.

This instruction sheet may be translated into oth-
er languages. In the event of any discrepancy,
the English version shall prevail.

TO THE INSTALLER:

 Give this sheet and the

operating instructions to the owner. Advise the
owner of any special operation or maintenance
information contained in the instructions.

TO THE OWNER:

 Save these instructions in

your owner’s kit. This sheet contains important
information for the use and maintenance of your
engine.

         

DANGER

Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided,
could result in death or serious injury

CAUTION

Indicates a hazardous situation which, if not avoided,
could result in minor or moderate personal injury.

NOTICE

Indicates an instruction which, if not followed, could
severely damage engine components or other prop-
erty.

Summary of Contents for EVINDURE ICON II













Reviews: