Browan BW2250 User Manual Download Page 64

Page: 64 / 75

BROWAN COMMUNICATIONS

Page

System | Configuration

Use the

System | Configuration

menu to configure such system utilities:

Backup – download current working system configuration for backup

Upload/Restore – upload system configuration for restore

Figure 71 – System Configuration settings

You can save your current device configuration file locally clicking the

Preparation

button:

Figure 72 – Backup settings

Such device configuration is saved in the specific format file (.cfg).

Description Message

shows the current version of firmware.

Click the

Preparation

button to start saving the configuration file.

Click the

Download

button to download current working configuration into your local PC.

Figure 73 – Download system configuration

A configuration file name will be required when you download/save the
configuration file. And please remember the configuration file name should only
include characters or numbers. Otherwise, this configuration file will not upload to
BW2250.

Summary of Contents for BW2250











































































Search results

Summary of Contents for BW2250

Reviews:

Browan BW2250, User Manual, Page: 64 / 75

Search results

Summary of Contents for BW2250

Reviews: