Brother P-Touch 580C User Manual Download Page 16 | Manualshive

Page: 16 / 188

background image

12

A single TZ tape cassette is supplied with this unit. However, since TZ tape cas-
settes and multi-color ink and tape cassettes are available for this machine in a
wide variety of colors and sizes, it is possible to make distinctive color-coded and
stylized labels.

In addition, this machine has been designed to allow you to change the tape
cassettes quickly and easily.

TO INSERT A TZ TAPE CASSETTE

(1) Press down on the cover release button and lift open the compartment

cover.

(2) If there is a cassette already in the compartment, remove it by pulling it

straight up.

(3) Remove the stopper from a new tape cassette and if the ink ribbon in the

cassette is loose, use your finger to wind the toothed wheel in the direction
of the arrow on the tape cassette until the ribbon is taut. If you are using an
old tape cassette, be sure the ribbon is taut before inserting it into the unit.

(4) Insert the tape cassette firmly into the compartment, making sure that the

entire back of the cassette contacts the bottom of the compartment.

+

When inserting the tape cassette, make sure that the inner ribbon does
not catch on the corner of the metal guide.

(5) Close the compartment cover, then turn on the machine if necessary.

(6) Press the

FEED

key once to advance the tape and remove any slack.

(7) Push down on the tape cutter lever to cut off the excess tape.

«
...
14
15
16
17
18
...
»

Summary of Contents for P-Touch 580C





























































































































































































Reviews:

No comments

Related manuals for P-Touch 580C

Brand: OBH Nordica Pages: 28

PROFESSIONAL BELGIAN IB08WR119

Brand: Waring Pages: 16

Brand: Profi Cook Pages: 42

Brand: Rowenta Pages: 60

Brand: Kalorik Pages: 24

Brand: Bunn Pages: 16

Brand: West Bend Pages: 33

Koro Prime Espresso

Brand: N&W Global Vending Pages: 68

Inissia EN 80.B

Brand: DeLonghi Pages: 13

Brand: Russell Hobbs Pages: 72

Brand: Koldfront Pages: 13

Brand: DAK Pages: 19

Brand: West Bend Pages: 40

Mini-Cappuccino

Brand: Newco Pages: 24

Brand: Harmony Pages: 10

BMF600XL - REV D10

Brand: Breville Pages: 60

Brand: Sencor Pages: 26

Brand: Keurig Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands