Brother NC-series User Manual Download

Page: 25 / 143

USER’S GUIDE

1-14

i. The other settings in the menu are not required. Push ESCAPE

several times to exit PCONSOLE.

j. Skip to the Assigning the remote printer name and number

sections below.

The following steps apply to configuring a remote printer on
NetWare 3.xx systems:

6.
a. Select Print Server Information from the PCONSOLE main menu

and choose the name of the PSERVER NLM.

b. Select Print Server Configuration and then Printer Configuration.

Select any "Not Installed" printer and press Enter. Remember the
number of this printer, since it will be used later in the configuration
process.

c. If desired, type in a new name for the printer.

d. Go to Type, press ENTER, highlight Remote Other/Unknown and

press ENTER again. The other settings in this menu are not required.

e. Push ESCAPE and save the changes.

f. Push ESCAPE and select Queues Serviced by Printer.

g. Highlight the printer name that you just configured and press

ENTER.

h. Press INSERT, choose the desired print queue, and press ENTER

(you can accept the default priority).

i. Press ESCAPE several times to exit PCONSOLE.

Summary of Contents for NC-series
















































































































































Search results

Summary of Contents for NC-series

Reviews:

Related manuals for NC-series

Brands by name

Popular brands

Brother NC-series, User Manual

Search results

Summary of Contents for NC-series

Reviews:

Related manuals for NC-series

Brands by name

Popular brands