manualshive.com logo in svg

Brother MFC-9140CDN, User Manual

Share
Download
Brother MFC-9140CDN User Manual Download Page 79

69

A

A

Replacing the consumable items

A

You must replace the consumable items when the machine indicates that the life of the 
consumable is over. You can replace the following consumable items by yourself:

Using non-Brother supplies may affect the print quality, hardware performance, and machine 
reliability.

NOTE

The drum unit and toner cartridge are two separate consumables. Make sure both are installed 
as an assembly. If the toner cartridge is placed in the machine without the drum unit, the 
message 

Drum !

 may be displayed.

 

Routine maintenance

A

Toner cartridge

Drum unit

See 

Replacing the toner cartridges

 on page 73.

Model Name: TN-281BK, TN-285C, TN-285M, 
TN-285Y

See 

Replacing the drum units

 on page 80.

Model Name: DR-281CL (4 pc. drum set) or 
DR-281CL-BK, DR-281CL-CMY (single drums)

 

 

Belt unit

Waste toner box

See 

Replacing the belt unit

 on page 86.

Model Name: BU-220CL

See 

Replacing the waste toner box

 on page 90.

Model Name: WT-220CL

 

 

Summary of Contents for MFC-9140CDN




















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands