manualshive.com logo in svg

Brother MFC-9140CDN, User Manual

Share
Download
Brother MFC-9140CDN User Manual Download Page 119

Routine maintenance 

109

A

d

Tightly wring out a lint-free cloth soaked 
in lukewarm water, and then wipe the 
separator pad (1) on the paper tray to 
remove dust.

 

e

Wipe the two pick-up rollers (1) inside 
the machine to remove dust.

 

f

Put the paper tray back in the machine.

g

Reload the paper and put the paper tray 
firmly back in the machine.

h

Turn on the machine.

Calibration

A

The output density for each colour may vary 
depending on the machine’s environment, 
such as temperature and humidity. 
Calibration helps you to improve the colour 
density.

a

Press .

b

Press 

Calibration

.

c

Press 

Calibrate

.

d

Press 

Yes

 to confirm.

e

The machine will display 

Completed

.

f

Press .

You can reset the calibration parameters 
back to the factory settings.

a

Press .

b

Press 

Calibration

.

c

Press 

Reset

.

d

Press 

Yes

 to confirm.

e

The machine will display 

Completed

.

f

Press .

1

1

Summary of Contents for MFC-9140CDN




















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands