Brother MFC-8370DN User Manual Download Page 41

Page: 41 / 215

Security features

Setting up the password

Note

• If you have already set the password, you

will not need to set it, again.

• If you forget the Memory Security

password, please call your Brother dealer.

Press

Menu

Enter a four-digit number for the
password using number 0-9.
Press

If the LCD shows

Verify:

, re-enter the

new password.
Press

Press

Stop/Exit

Changing the Memory
Security password

Press

Menu

Press

to choose

Set Password

Press

Enter your four-digit password.
Press

Enter a four-digit number for the new
password.
Press

If the LCD shows

Verify:

, re-enter the

new password.
Press

Press

Stop/Exit

Turning Memory Security
on/off

If you enter the wrong password, when
following the instruction below, the LCD will
show

Wrong Password

. Re-enter the

correct password.

Turning Memory Security on

Press

Menu

Press

to choose

Set Security

Press

Enter the registered four-digit password.
Press

The machine goes offline and the LCD
shows

Secure Mode

Note

If there is a power failure the data will stay
in memory for up to 4 days.

Turning Memory Security off

Press

Menu

Enter the registered four-digit password.
Press

Memory Security is automatically turned
off and the LCD shows the date and
time.

Note

If you enter the wrong password, the LCD
shows

Wrong Password

and stays

offline. The machine will stay in Secure
Mode until the registered password is
entered.

Summary of Contents for MFC-8370DN
























































































































































































































Search results

Summary of Contents for MFC-8370DN

Reviews:

Brands by name

Popular brands

Brother MFC-8370DN, User Manual

Search results

Summary of Contents for MFC-8370DN

Reviews:

Brands by name

Popular brands