manualshive.com logo in svg

Brother MFC-8370DN, User Manual

Share
Download
Brother MFC-8370DN User Manual Download Page 24

Chapter 2

14

Acceptable paper and 

other print media

2

Print quality may vary according to the type of 
paper you are using.

You can use the following types of print 
media: thin paper, plain paper, thick paper, 
bond paper, recycled paper, transparencies, 
labels or envelopes.

For best results, follow the instructions below:

„

Use paper made for plain paper copying. 

„

Use paper that is 60 to 105 gsm.

„

Use labels and transparencies which are 
designed for use in laser machines.

„

DO NOT put different types of paper in the 
paper tray at the same time because it 
may cause paper jams or misfeeds.

„

For correct printing, you must choose the 
same paper size from your software 
application as the paper in the tray.

„

Avoid touching the printed surface of the 
paper immediately after printing.

„

When you use transparencies remove 
each sheet immediately to prevent 
smudging or paper jams.

„

Use long grain paper with a neutral Ph 
value, and a moisture content of approx. 
5%.

Type and size of paper

2

The machine loads paper from the installed 
standard paper tray, optional lower tray 
(MFC-8380DN) or multi-purpose tray.

Standard paper tray

2

Since the standard paper tray is a universal 
type, you can use any of the paper sizes (one 
paper type and size at a time) listed in the 
table in 

Paper capacity of the paper trays

 

on page 15. The standard paper tray can 
hold up to 250 sheets of Letter/A4, Legal or 
Folio size paper (80 gsm). Paper can be 
loaded up to the maximum paper mark on the 
sliding paper width guide.

Multi-purpose tray (MP tray)

2

The MP tray can hold up to 50 sheets of plain 
paper (80 gsm) or up to 3 envelopes. Paper 
can be loaded up to the maximum paper mark 
on the sliding paper width guide.

Optional lower tray (LT-5300) 
(MFC-8380DN)

2

The optional lower tray can hold up to 250 
sheets of Letter/A4, Legal and Folio size 
paper (80 gsm). Paper can be loaded up to 
the top line of the maximum paper mark on 
the sliding paper width guide.

The name for the paper trays in the 
printer driver in this Guide are as 
follows:

2

Tray and optional unit

Name

Standard paper tray

Tray 1

Optional lower tray
(MFC-8380DN)

Tray 2

Multi-purpose tray

MP tray

Summary of Contents for MFC-8370DN
























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands