Brother Innov-is NV4000D Service Manual Download Page 329 | Manualshive

Page: 329 / 381

background image

5 - 3

Electronic Parts

Failure Investigation for Electronic Parts The power does not come on

When the power is turned on,
nothing appears on the LCD.

N

Connect the power supply
cord correctly or replace it.

N

Y

Y

Connect the inlet assembly
(D6) correctly or replace it.

N

Is lead wire A on the main panel free from
damage and correctly connected to the
main PCB (CN17) and panel PCB (CN1)?

N

Y

Connect lead wire A on the main
panel correctly or replace it.

Is lead wire B on the main panel free from
damage and correctly connected to the
main PCB (CN12) and panel PCB (CN3)?

N

N

Y

When lead wires A and B on the main panel are
removed from the main PCB and power is turned on in
the "no-front-cover test" mode, does the buzzer sound?

N

Y

Replace the power supply
unit (D6).

Y

Connect lead wire B on the main
panel correctly or replace it.

Replace the power PCB.

Y

Replace the power supply
unit (D6).

When the power is turned on, does
the buzzer sound after a while?

Is the power supply cord free from
damage and connected correctly?

Is the inlet assembly (D6) free from damage
and correctly connected to the power PCB?

To next page

When the power PCB connector (main PCB
(CN13)) is disconnected, are the voltages
between pins 5 & 6 and pins 8 & 6 normal?
Between pins 5 & 6: 4.75 - 5.25 V DC
Between pins 8 & 6: 24.7 - 27.3 V DC

«
...
327
328
329
330
331
...
»

Summary of Contents for Innov-is NV4000D






























































































































































































































































































































































































Reviews:

No comments

Related manuals for Innov-is NV4000D

Brand: Janome Pages: 42

Brand: ServiceMaster Pages: 12

Brand: Janome Pages: 40

HAKOMATIC B 90 CL

Brand: HAKO Pages: 42

Minoltafax 1600e

Brand: Konica Minolta Pages: 127

Brand: JUKI Pages: 64

Brand: Mi-T-M Pages: 2

Brand: Square Scrub Pages: 9

Brand: Frister Rossmann Pages: 22

Brand: Nilfisk-Advance Pages: 38

Brand: Chauvet Pages: 20

Brand: Necchi Pages: 80

Brand: Necchi Pages: 92

Brand: Riccar Pages: 16

Brand: Fellowes Pages: 7

Brand: Yamaha Pages: 30

Brand: Sunny Health & Fitness Pages: 24

SPS/E-1306 Series

Brand: SunStar Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands