Brother Innov-is NV4000D Service Manual Download Page 300

Page: 300 / 381

4 - 6

Adjustment

Three point needle drop adjustment

1. Remove the front cover, and turn the power on while pressing [SW3] and [SW4] on the main PCB assembly.

2. Press [SW4] (select test mode "4" when the front cover is attached).

3. Turn the pulley by hand until the tip of the needle enters the needle hole.

4. Loosen the socket bolt (M3X10) of the zigzag adjusting nut.

5. Adjust the zigzag adjusting nut so that the needle drop is centered over the needle hole on needle plate A at the

left base line, center base line, and right base line.

6. Tighten the socket bolt (M3X10).

Zigzag adjusting nut

Screw 3x10

Summary of Contents for Innov-is NV4000D






























































































































































































































































































































































































Search results

Summary of Contents for Innov-is NV4000D

Reviews:

Related manuals for Innov-is NV4000D

Brands by name

Popular brands

Brother Innov-is NV4000D, Service Manual

Search results

Summary of Contents for Innov-is NV4000D

Reviews:

Related manuals for Innov-is NV4000D

Brands by name

Popular brands