Brother HL-S7000DN Series Service Manual Download Page 445 | Manualshive

Page: 445 / 460

background image

5-57

Confidential

2.2 Reset for the Periodical Replacement Part

This function is used to reset the relevant part counter when the user replaced a periodical
replacement part with the correct procedure, and also used to forcibly reset the relevant part
counter when an error cannot be resolved because the user did not replace a consumable part
with the correct procedure.

<Operating procedure>

(1) While the machine is in the ready state, press the

Go

and

buttons at the same time.

"Reset Menu" is displayed on the LCD.

(2) Press the

or

button to select the periodical replacement part to be reset, and press

the

OK

button. "1.Reset 2.Exit" is displayed on the LCD.

(3) Press the

1

button. "Accepted" is displayed on the LCD, and the machine returns to the

ready state.

The periodical replacement parts that can be reset are as follows.

- PF Kit MP

- Air Filter Case (Air filter)

- PF Kit 1

- Sub tank (Sub tank ASSY)

- PF Kit 2

- CR frame Unit (Carriage unit)

- PF Kit 3

- Platen (Platen frame)

- PF Kit 4

- Ink Supply Unit (Ink refill unit)

- Waste Tank (Waste ink box)

- Drive Frame (Drive switching unit)

- Print Head Black (Ink head)

- Optimizer Unit (Humidify unit)

- Print Head Pre-C (Pre-coat head)

- Leak Sensor

(Waste ink box leak sensor/Leak sensor )

«
...
443
444
445
446
447
...
»

Summary of Contents for HL-S7000DN Series













































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HL-S7000DN Series

Brand: MAKERGEAR Pages: 8

Brand: Malyan Pages: 9

Brand: Xerox Pages: 341

Brand: Xante Pages: 21

Brand: Pinnacle Technology Pages: 76

Brand: Geeetech Pages: 94

Brand: Konica Minolta Pages: 61

Brand: OKIDATA Pages: 44

Brand: Oki Pages: 2

Brand: Noztek Pages: 8

BradyPrinter A5500

Brand: Brady Pages: 72

Brand: Evolis Pages: 45

Brand: RHINO Pages: 21

Brand: TonerRefillKits Pages: 10

Brand: Printekmobile Pages: 2

Brand: Z Corporation Pages: 12

Brand: Oki Pages: 9

Brand: Boley Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands