Brother HL-5580D Service Manual Download Page 124

Page: 124 / 433

2-98

Confidential

4.3 Troubleshooting for Image Defects

4.3.1 Image defect examples

Fig. 2-11

Light (2-99)

Faulty registration
(2-100)

Dark (2-100)

Poor fixing
(2-101)

Completely
blank (2-101)

Image distortion
(2-102)

All black
(2-102)

Dirt on the paper (2-103)

Vertical streaks (2-103)

Black vertical
streaks on a light
background (2-104)

Horizontal
streaks (2-104)

White vertical
streaks (2-104)

White horizontal
streaks (2-105)

Faint print (2-105)

White spots
(2-106)

Single-colored dot
or dirt (2-106)

Black band
(2-107)

Downward
fogging of solid
color (2-109)

Horizontal lines (2-109)

Ghost (2-109)

Fogging (2-110)

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Search results

Summary of Contents for HL-5580D

Reviews:

Brands by name

Popular brands

Brother HL-5580D, Service Manual

Search results

Summary of Contents for HL-5580D

Reviews:

Brands by name

Popular brands