manualshive.com logo in svg

Brother HL-5250DN series, Service Manual

Share
Download
Brother HL-5250DN series Service Manual Download Page 141

HL-5240/5250DN/5270DN/5280DW SERVICE MANUAL 

Confidential 

4-27

3.3 

Paper Feeding Problems 

Even if the paper is printed and ejected without any problems such as paper jams, paper 
feeding problems below may appear.  

Users can clear these problems by following the ‘User Check’ items for each problem.  Even if 
the same problem occurs again, follow the procedures in the table below. 

 

(1) Double feeding 

 

User Check 

Check the paper used meets the recommended paper specifications.

 (Refer to

 3.6 “Paper” in 

Chapter 1.

)

 

 

Possible cause 

Step

Check 

Result

Remedy

 

Separation pad 

1 

Is the surface of the separation 
pad worn out? 

Yes 

Replace the separation pad. 

 
(2) Wrinkles or creases 

 

User Check 

(1) Check that paper is loaded into the paper tray correctly. 

(2) Check the paper used meets the recommended paper specifications. (Refer to 

3.6 “Paper” in 

Chapter 1

.) 

(3) Try printing using the straight-through output path. 

(4) Turn over the stack of paper in the tray or try rotating the paper 180° in the tray.

 

(5) For the envelope, check the setting of the nip action in the fuser unit.

 

 

Possible cause 

Step

Check 

Result

Remedy

 

Paper 

1 

Is the problem solved if new 
paper is used? 

Yes 

Instruct the user how to store 
paper so that it does not 
absorb moisture. 

Fuser unit 
entrance guide 

2 

Is the entrance guide dirty? 

Yes 

Clean the entrance guide. 

Fuser unit 

3 

Is the pressure roller dirty? 

Yes 

Clean the pressure roller. 

 

 

 

No 

Replace the fuser unit. 

 

(3) Page skew 

 

User Check 

(1) Check that the paper or other media is loaded into the paper tray correctly and that the paper 

guides are not too tight or too loose against the paper stack. 

(2) If using the manual feed slot, check how to load paper into the manual feed slot correctly. 

(3) The paper tray may be too full.  Load paper below        mark in depth. 

(4) Check the paper used meets the recommended paper specifications. (Refer to

 3.6 “Paper” in 

Chapter 1.

) 

(5) Check that the levers on the left and right hand sides for the nip action in the fuser unit are nipped 

equally.

 

Summary of Contents for HL-5250DN series


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands