Brother HL-4140CN Technical Reference Manual Download | Manualshive

Page: 67 / 517

background image

CHAPTER 2 PCL - 48

5.1.4.

Bound fonts

Bound fonts are fonts which have only a single symbol set.

5.1.5.

Unbound fonts

Unbound fonts are fonts which have a large amount of symbols selected from a complementary symbol index

(intellifont) or unicode symbol index (TrueType).

5.1.6.

Font sources

Depending on your printer model, fonts available to the printer can be in one of three places, either in the

printer's ROM as supplied from the factory, on a cartridge/card, on the storage device, or in the printer's RAM.

RAM fonts are downloaded from a personal computer.

5.1.7.

Internal fonts

The printer comes with some bitmap fonts contained in its ROM and many scalable typefaces which can be used

to create scalable fonts.

5.1.8.

Card/cartridge fonts

You can buy cartridge/card -based bitmap fonts and scalable typefaces. Plug the cartridge/card into one of the

printer's cartridge/card slots and then select any font from them as if it were in the printer's ROM. Depending on

your model, you can also save bitmap fonts and scalable typeface in the flash ROM memory, installed optional

storage device and you can use any of these as if they were a font card.

5.1.9.

Downloadable fonts

You can buy diskettes containing fonts which can be copied directly to the printer using the DOS COPY

command. You can also design your own fonts and download them to the printer.

One disadvantage of downloaded fonts is that they reside in the printer's RAM memory. The printer also uses

this memory for composing the text and graphic output that it prints on the page. If the memory contains too

many fonts the printer may run out of memory. Since downloaded fonts are stored in the printer's RAM they are

lost when the printer is switched off, and you must download them again before you can use them.

5.1.10.

Primary and secondary fonts

The printer maintains two sets of font characteristics which define its primary and secondary fonts. The primary
font is the one it will use by default, the secondary font can be selected instead. This facility enables you to have
two parallel font definitions that you can switch between easily without invoking long escape sequences. You
can select the primary and secondary fonts using PCL commands.

Depending on your model, you can also set any available fonts to be the printer's user default primary and
secondary fonts using the printer's control panel. Refer to the User Guide for instructions on how to do this.

The factory default settings for both primary and secondary fonts are Brougham 12 point, 10 cpi Roman 8.

5.1.11.

Specifying the primary font

When you specify primary font characteristics you send escape codes with '(' as the second character of the
sequence. This tells the printer that the font characteristic you are specifying applies to the primary font.

5.1.12.

Specifying the secondary font

When you specify secondary font characteristics you send escape codes with ')' as the second character of the
sequence. This tells the printer that the font characteristic you are specifying applies to the secondary font.

«
...
65
66
67
68
69
...
»

Summary of Contents for HL-4140CN






































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HL-4140CN

Brand: Canon Pages: 11

imageRUNNER ADVANCE 8085

Brand: Canon Pages: 176

Brand: Canon Pages: 85

imageRUNNER 5070

Brand: Canon Pages: 4

imageRUNNER 5570

Brand: Canon Pages: 4

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 8

IMAGERUNNER 7105

Brand: Canon Pages: 21

Brand: Canon Pages: 58

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 12

imageRUNNER ADVANCE C2020

Brand: Canon Pages: 68

imageRUNNER ADVANCE 6055

Brand: Canon Pages: 134

Color imageRUNNER LBP5970

Brand: Canon Pages: 67

FAXPHONE L170 - B/W Laser - Copier

Brand: Canon Pages: 12

Brand: Canon Pages: 2

imageRunner 1133

Brand: Canon Pages: 60

Color imageCLASS MF8280Cw

Brand: Canon Pages: 36

Brand: Canon Pages: 104

imagePROGRAF iPF8300

Brand: Canon Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands