manualshive.com logo in svg

Brother HL-3040CN, Service Manual, Page: 92 / 437

Share
Download
Brother HL-3040CN Service Manual Download Page 92

3-28

Confidential

■

Error code 60 (C), 61 (M), 62 (Y), 63 (K)

Toner cartridge is at the end of life. (The counter value of the develop roller reaches the end of 
life, or the toner sensor detects toner empty.)

<

User Check

>

- Gently shake the toner cartridge of the appropriate color from side to side and install it again.

- Replace the toner cartridge of the appropriate color.

Replace Toner
Open the Top Cover, replace Toner Cartridge. Cyan (C).

Replace Toner
Open the Top Cover, replace Toner Cartridge. Magenta (M).

Replace Toner
Open the Top Cover, replace Toner Cartridge. Yellow (Y).

Replace Toner
Open the Top Cover, replace Toner Cartridge. Black (K).

Step

Cause

Remedy

1

HVPS control PCB failure

Replace the HVPS control PCB ASSY.

2

Engine PCB failure

Replace the engine PCB ASSY.

3

Main PCB failure

Replace the main PCB ASSY.

4

Harness connection failure of 
toner/new sensor PCB ASSY

Check the sensor performance following 
the procedure described in 

“Function code 

32”

. 

 If any problem occurs, check the harness 
connection of the toner/new sensor PCB 
ASSY of the appropriate color, then 
reconnect it.

5

Toner/new sensor PCB failure

Replace the toner/new sensor PCB ASSY.

Summary of Contents for HL-3040CN






















































































































































































































































































































































































































































Reviews:

No comments