manualshive.com logo in svg

Brother DCP-T220, User Manual

Share
Download
Brother DCP-T220 User Manual Download Page 189

 Home > 

Routine Maintenance

 > Refill the Ink Tanks

Refill the Ink Tanks

Make sure to confirm the actual amount of remaining ink visually by looking through the window (1) of the ink
tank. If the remaining ink level is at or below the lower line (2) under the minimum fill mark, refill the ink tank.

2

1

The ink below the lower line is necessary to prevent air from drying out and damaging the print head assembly.
Refill the ink tank when the remaining ink level is at or below the lower line.

  CAUTION

If ink gets into your eyes, rinse them with water immediately. If left as it is, it may cause red eye or mild
inflammation. In case of any abnormality, consult your doctor.

IMPORTANT

•

Brother strongly recommends that you continue to use only Brother Original replacement ink designed for
your model. Use or attempted use of potentially incompatible ink in the Brother machine may cause
damage to the machine and/or may result in unsatisfactory print quality. Our warranty coverage does not
apply to any problem that is caused by the use of unauthorised third-party ink. To protect your investment
and obtain premium performance from the Brother machine, we strongly recommend the use of Brother
Original ink.

•

Check the ink bottle model name on the label. Using the incorrect ink may cause damage to the machine.

BTD60BK

BT5000CMY

BT5001CMY

BT5009CMY

BT6000BK

BT6001BK

BT6009BK

1. Open the ink tank cover (1).

1

185

Summary of Contents for DCP-T220














































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands