manualshive.com logo in svg

Brother DCP-T220, User Manual

Share
Download
Brother DCP-T220 User Manual Download Page 163

 Home > 

Troubleshooting

 > Error and Maintenance LED Indications

Error and Maintenance LED Indications

As with any sophisticated office product, errors may occur and supply items may have to be replaced. If this
happens, your machine identifies the error or required routine maintenance and indicates this with the LEDs on
the control panel. The LED indications are explained in this table.
You can correct most errors and perform routine maintenance yourself. If you need more tips, go to your model's

FAQs & Troubleshooting

 page at 

support.brother.com

.

•

Related Information

 references are at the bottom of this page.

LED

Description

The LED is off.

The LED is lit.

The LED is blinking.

LED

Status

Cause

Action

Tray not detected

The paper tray is not completely
inserted.

Slowly push the paper tray
completely into the machine.

Paper or a foreign object has prevented
the paper tray from being inserted
correctly.

Pull the paper tray out of the
machine, and remove the jammed
paper or foreign object. If you
cannot find or remove the jammed
paper, see 

Related Information

:

Printer Jam or Paper Jam

.

No paper fed

The machine is out of paper or paper is
not correctly loaded in the paper tray.

Do one of the following:
•

Refill the paper tray, and then
press 

Mono Start

 or 

Colour

Start

.

•

Remove and reload the paper,
and then press 

Mono Start

 or

Colour Start

.

See 

Related Information

: 

Load

Paper

.

The paper was not inserted in the
centre position of the manual feed slot.

Remove the paper and reinsert it in
the centre of the manual feed slot,
and then press 

Mono Start

 or

Colour Start

.

See 

Related Information

: 

Load

Paper in the Manual Feed Slot

.

The Jam Clear Cover is not closed
correctly.

Make sure the Jam Clear Cover is
closed evenly at both ends.
See 

Related Information

: 

Paper is

Jammed Inside the Machine

.

Paper dust has accumulated on the
surface of the paper pick-up rollers.

Clean the paper pick-up rollers.
See 

Related Information

: 

Clean the

Paper Pick-up Rollers

.

159

Summary of Contents for DCP-T220














































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands