manualshive.com logo in svg

Brother DCP-9055CDN, Service Manual

The Brother DCP-9055CDN is a versatile all-in-one printer that offers professional-quality printing, scanning, and copying functions. To get started with this feature-packed device, simply download the free Basic User's Manual from our website and follow the easy instructions.

Share
Download
background image

5-38

Confidential

1.4.18 Adjustment of touch panel (Function code 61) 

<Function>

This function adjusts the detection area on the touch panel. 

<Operating procedure>

(1) Press the 

6

 and 

1

 buttons in this order in the initial state of the maintenance mode.  

The adjustment screens shown below appear on the LCD. 

(2) Touch the symbols on the touch panel with a stylus in the order of top-left, bottom-left,  

bottom-right, top-right, and the center.  After a symbol touched disappears, touch the next  
one. 

Fig. 5-21

When you press the symbol at the center (the 5th symbol), "OK" appears if the specified area 
is correctly adjusted.  Then, the screen shown below appears, and the machine returns to the 
initial state of the maintenance mode in approximately 3 seconds.

In the case of "NG", repeat this operation 2 to 3 times.  If "NG" remains displayed even after 
the operation is repeated, check if there is harness connection failure in the touch panel, 
disconnection, short-circuit, or entry of foreign objects in the touch panel frame.  Although any 
of these problems is not observed, if "NG" is displayed, replace the LCD unit.

Note: 

The adjustment procedure requires a stylus with a thin tip.  A commercially available stylus 
designed for electronic dictionaries or personal digital assistance (PDA) can be used.  If  
you do not have it on hand, order the "STYLUS" from the Brother's parts list.  

Note: 

- Do not use tools other than a pen designed for touch panels.  Especially, never use a  

pointed one, e.g., a screwdriver.  Using such a tool damages the touch panel.  

- Do not touch the touch panel with fingers.  The contact area of a finger is too large  to 

adjust the touch panel precisely. 

- If no keys are pressed for one minute in the above procedure or you press the 

Stop/Exit

 

button, the machine stops the procedure and returns to the initial stage of the  
maintenance mode. 

Note: 

If the way to press the symbol is wrong, or if a wrong place is pressed, "NG" appears on the 
LCD, and the machine returns to the screen in step (2) in approximately 3 seconds.  Be 
sure to press the symbols from the top-left in the order shown above.

Summary of Contents for DCP-9055CDN





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DCP-9055CDN

Unisys 115 Operation/Reference Manual preview
115
Brand: Unisys Pages: 255
Xerox B210 User Manual preview
B210
Brand: Xerox Pages: 199
Oki B2200 Maintenance Manual preview
B2200
Brand: Oki Pages: 100
Oki B2200 Quick Setup Manual preview
B2200
Brand: Oki Pages: 2
Xerox B235 User Manual preview
B235
Brand: Xerox Pages: 316
Xerox B215 Get Started preview
B215
Brand: Xerox Pages: 74
Xerox B215 User Manual preview
B215
Brand: Xerox Pages: 306
Xerox B215 Quick Use Manual preview
B215
Brand: Xerox Pages: 16
Xerox B210 Quick Start Manual preview
B210
Brand: Xerox Pages: 4
Oki B2200 Guide Utilisateur preview
B2200
Brand: Oki Pages: 38
Oki B2200 Guía Del Usuario preview
B2200
Brand: Oki Pages: 38
Oki B2200 User Manual preview
B2200
Brand: Oki Pages: 36
Oki B2200 Safety & Warranty preview
B2200
Brand: Oki Pages: 36
Samsung MFP SCX-6345N Manual Del Usuario preview
MFP SCX-6345N
Brand: Samsung Pages: 165
Samsung Inkjet SF-430 Quick Install Manual preview
Inkjet SF-430
Brand: Samsung Pages: 2
Samsung Inkjet SCX-1150F Repair Manual preview
Inkjet SCX-1150F
Brand: Samsung Pages: 66
Samsung CLX-6220FX User Manual preview
CLX-6220FX
Brand: Samsung Pages: 155
Samsung CLX-3170FN series User Manual preview
CLX-3170FN series
Brand: Samsung Pages: 220

Brands by name

Popular brands

Load more brands