manualshive.com logo in svg

Brother DCP-9055CDN, Service Manual

Share
Download
Brother DCP-9055CDN Service Manual Download Page 419

5-20

Confidential

1.4.10 Operational check of sensors (Function code 32)

<Function>

This function allows you to check each of the sensors.

<Operating procedure>

(1) Press the 

3

 and 

2

 buttons in this order in the initial state of the maintenance mode.

(2) The machine beeps 1,100 Hz and 400 Hz tones cyclically through the following volumes 

for testing the speaker.  To stop beeping, press the 

OK

 button.

Fig. 5-12

If the sensing status are as listed below, the LCD will show "C1C2L2T2**" when paper 
tray 2 is installed.  "C1********" appears on the LCD when paper tray 2 is not installed.  
Press the 

Start/Black

 button to check the next item.

Given below is the relationship between the LCD indication, sensor name and sensor 
state.

LCD

Sensors

Sensing status (OK/NG)

C1

T1 paper edge sensor

Paper tray 1 not installed/installed

C2

T2 paper edge sensor

Paper tray 2 not installed/installed

L2

T2 plate-up detection sensor

Plate down/Plate up

T2

T2 connector

Paper tray 2 installed/not installed

MP

MP paper empty sensor

MP tray paper not detected/detected

MR

MP registration front sensor

MP tray paper not detected/detected

CV

Front cover sensor

Front cover closed/open

RC

Back cover sensor

Back cover closed/open

RM

Registration front sensor

Paper not detected/detected

RA

Registration rear sensor

Paper not detected/detected

PO

Paper eject sensor

Paper not detected/detected

FW

Waste toner sensor

Light shielded on sensor/Light guided to sensor

NK

New toner sensor Black

OFF/ON

NY

New toner sensor Yellow

OFF/ON

NM

New toner sensor Magenta

OFF/ON

NC

New toner sensor Cyan

OFF/ON

KC

Toner sensor Black

Toner (K) detected/not detected

YC

Toner sensor Yellow

Toner (Y) detected/not detected

MC

Toner sensor Magenta

Toner (M) detected/not detected

CC

Toner sensor Cyan

Toner (C) detected/not detected

Note: 

- The "--" appears on the LCD if there is no display. 

- The "**" appears on the LCD if the parts are not installed or there is no item.

OFF

400 Hz

Low       Medium        High

1,100 Hz

High      Medium        Low

OFF

Summary of Contents for DCP-9055CDN





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands