manualshive.com logo in svg

Brother DCP-9045CDN, Service Manual

Share
Download
Brother DCP-9045CDN Service Manual Download Page 95

Confidential 

2-1

CHAPTER 2   PERIODICAL MAINTENANCE 

To avoid creating secondary problems by mishandling, follow the warnings below during 
maintenance work. 

 

WARNING 

- Always turn off the power switch and unplug the power cord from the power outlet before 

accessing any parts inside the machine. 

- When opening the front cover or back cover to access any parts inside the machine, never 

touch the shaded parts shown in the following figures. 

 

 

1.     

CONSUMABLE PARTS

 

The consumable parts described in this section are parts which are subject to deterioration or 
damage and should be replaced at least once during the period of warranty of the product if 
any printing quality problem appears. 

Parts

 

Approximate Life

 

Standard cartridge 

Approx. 2,500 pages A4/Letter pages @ 
5% coverage 

Black 

High-capacity 
cartridge 

Approx. 5,000 pages A4/Letter pages @ 
5% coverage 

Standard cartridge 

Approx. 1,500 pages A4/Letter pages @ 
5% coverage 

Toner Cartridge

Cyan, 
Magenta, 
Yellow 

High-capacity 
cartridge 

Approx. 4,000 pages A4/Letter pages @ 
5% coverage 

Drum Unit 

Approx. 17,000 pages A4/Letter pages 
Life expectancy will vary depending on 
number of continuous printing pages. 
(Refer to 

“Life of Drum Unit”

.) 

Belt Unit 

Approx. 50,000 pages A4/Letter pages 
Life expectancy will vary depending on 
number of continuous printing pages. 
(Refer to 

“Life of Belt Unit”

.) 

Waste Toner Box 

Approx. 20,000 pages A4/Letter pages @ 
5% coverage for CMYK each 

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands