Brother DCP-9045CDN Service Manual Download Page 61

Page: 61 / 491

Confidential

1-42

3.3 Paper Jam

Paper jam in the paper tray and front cover

Step

Cause

Check

Result

Remedy

1 Belt

unit

malfunction

Does the belt unit move
correctly?

Replace the belt unit.

2 Registration

front

actuator move
smoothly or
catching in some
position

Does the registration front
actuator move smoothly?

No Re-assemble

the

registration front actuator.

3 T1

registration

front sensor
failure

Does T1 registration front
sensor move smoothly?
(Check it following the
procedure described in

“Maintenance mode 32”

Replace the front door
unit ASSY.

Paper jam in the back cover and paper eject section

Step

Cause

Check

Result

Remedy

1 Foreign

object

around fuser unit

Is there a foreign object
around the fuser unit?

Yes

Remove the foreign
object.

Paper eject ASSY
malfunction

Is each pinch roller of the
paper eject ASSY
attached to each paper
eject roller properly?

Replace the paper eject
ASSY.

3 Paper

eject

actuator failure

Does the paper eject
actuator move smoothly?
Is it damaged?

Replace the fuser unit.

Paper jam in the DX paper feeding section

User Check

- Use the A4 size paper.
- Use paper which has not curled.
- Do not use too thin paper.

- Check that the DX paper size (A4/Letter) switch lever of the DX feed ASSY is placed in the

correct position.

Step

Cause

Check

Result

Remedy

Deformation of
paper guide DX
on the bottom of
the paper tray

Is the paper guide DX
deformed?

Replace the paper tray.

DX feed ASSY
failure

Is the DX feed ASSY
deformed?
Do the rollers of the DX
feed ASSY move
correctly?

Replace the DX feed
ASSY.

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands