manualshive.com logo in svg

Brother DCP-9045CDN, Service Manual

Share
Download
Brother DCP-9045CDN Service Manual Download Page 363

Confidential 

5-3

1.4    Detailed Description of Maintenance-mode Functions 

1.4.1  EEPROM Parameter Initialization (Function code 01, 91) 

<Function> 

The machine initializes the parameter, user switches, worker switches and assurance mode 
switch settings registered in the EEPROM, to the initial values. Entering function code 01 
initializes almost all of the EEPROM areas, but entering 91 does not initialize some areas, as 
listed below. 

Function code

Data item 

01 91 

Maintenance-mode functions 

User switches 
Worker switch (Refer to 

Appendix 1

.)

These will be initialized. 

Remote activation code 
Registered message for cover page 
comment 
Forwarding / paging number, PIN 
number 
Outside line number 
Telephone function registration 
One-touch dialing 
Speed dialing 
Group dialing 

All of these will be 

initialized. 

These will 

not

 be 

initialized. 

Note: 

If you replace the main PCB with the one used for any other machine, carry out this procedure 
and then customize the EEPROM (maintenance-mode function code 74 in 

Section 1.4.20

). 

<Operating Procedure> 

(1) Press 

the 

0

 and 

1

 buttons (or the 

9

 and 

1

 buttons according to your need) in this order in 

the initial stage of the maintenance mode. 
The “PARAMETER INIT” will appear on the LCD. 

(2)  Upon completion of parameter initialization, the machine beeps for one second and 

returns to the initial stage of the maintenance mode.  

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands