Brother DCP-9045CDN Service Manual Download Page 355

Page: 355 / 491

Confidential

4-11

2. IF YOU REPLACE THE ENGINE PCB

< What to do when replacing the engine PCB >

Rewriting the Firmware (Engine Firmware)

Performing the Color Calibration

Performing the Auto Registration

< Which parts to use >

- Engine PCB: The table below shows the ROM type.

Flash ROM 0 (512 Kbyte): Engine firmware

< What you need to prepare >

(1) Computer (Windows



XP/2000)

Create a folder on the C drive, for example: - (AC FIRMWARE)

(2) A USB flash memory drive
(3) The firmware

Engine firmware:
LZ0833_A.djf

LZXXXX_$.djf
LZXXXX: First six digits are a parts number of the firmware.

$: Alphabet representing the revision of the

firmware.

< Procedures >

Rewriting the Firmware (Engine Firmware)

- How to rewrite the firmware by using the USB flash memory drive

Note:

- Make sure that the USB flash memory drive has enough space to save the program file.

- If you want to print an index of the files, choose “Index Print”. The “Index Print” selection

can be found after you scroll down through all the file names. Press the

button.

(1) Save the necessary program file (Engine firmware) to rewrite it into the USB flash

memory drive.

(2) Connect the USB flash memory drive to the USB direct Interface on the front of the

machine.

Fig. 4-2

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands