manualshive.com logo in svg

Brother DCP-9045CDN, Service Manual

Share
Download
Brother DCP-9045CDN Service Manual Download Page 28

Confidential 

1-9

 Error code 25 

Print Unable 25

 

Turn the power off and then back on again.

 

Develop drive motor failure 

Error code 26 

Print Unable 26

 

Turn the power off and then back on again.

 

Belt drive motor failure 

Error code 27 

Print Unable 27

 

Turn the power off and then back on again.

 

Paper feed/belt cleaner motor failure 

Step

 

Cause

 

Remedy

 

1 

Motor harness connection 
failure 

Check the harness connection of the appropriate 
motor and reconnect it. 

2 

Motor failure 

Replace the appropriate motor. 

3 

Engine PCB failure 

Replace the engine PCB ASSY. 

4 

Low-voltage power supply 
PCB failure 

Replace the PS PCB unit. 

 Error code 28 

Print Unable 28

 

Turn the power off and then back on again.

 

Drum drive motor 1 (K, Y) failure 

Error code 29 

Print Unable 29

 

Turn the power off and then back on again.

 

Drum drive motor 2 (M, C) failure 

Step

 

Cause

 

Remedy

 

1 

Drum drive motor harness 
connection failure 

Check the harness connection of the drum drive 
motor and reconnect it. 

2 

Drum phase sensor PCB 
failure 

Replace the drum phase sensor PCB ASSY. 

3 

Drum drive motor failure 

Replace the drum drive motor. 

4 

Engine PCB failure 

Replace the engine PCB ASSY. 

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands