manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 86

2-49

Confidential

■

Error code 85

These errors do not usually occur in the normal use. The conceivable causes are noise around 
the installation site, fluctuation of the power supply voltage, and failures in the software.

Error, which cannot be specified, occurs.

Error code 86

Error, which cannot be specified, occurs.

Error code 87

Error, which cannot be specified, occurs.

■

Error code 88

Paper jam inside the machine.

No Tray
A Tray is not detected, install #T.

No Tray
A Tray is not detected, install #T.

---

<User Check>

• Turn OFF the power switch, and turn it ON again after a while.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

Jam Inside
Open the Front Cover, pull out the Drum Unit completely and remove
the jammed paper.

<User Check>

• Check if the paper is jammed. If jammed, remove it.

Step

Cause

Remedy

1

Harness connection failure of 

paper eject sensor PCB ASSY

Check the harness connection of the paper 

eject sensor PCB ASSY and reconnect it.

2

Paper eject actuator catching on 

some position

Correct the position of the paper eject 

actuator.

3

Paper eject sensor PCB failure

Replace the paper eject sensor PCB 

ASSY.

4

Fuser unit

 

gear damaged

Replace the Fuser unit.

5

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands