manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 104

2-67

Confidential

■

Error code E2

When the center thermistor is lower than the idle temperature, it is detected that the side 
thermistor temperature is higher than 280 °C.

■

Error code E3, E4

These errors do not usually occur in the normal use. The conceivable causes are noise around 
the installation site, fluctuation of the power supply voltage, and failures in the software.

Error, which cannot be specified, occurs.

■

Error code E6

Write error in EEPROM of the main PCB.

Print Unable XX
Turn the power off and then back on again.

Step

Cause

Remedy

1

Heat roller dirty

Clean the heat roller.

2

Harness connection failure 

between paper eject sensor PCB 

ASSY and fuser unit

Check the harness connection between the 

paper eject sensor PCB ASSY and fuser 

unit, and reconnect it.

3

Side thermistor or center 

thermistor failure

Replace the fuser unit.

4

Paper eject sensor PCB failure

Replace the paper eject sensor PCB 

ASSY.

5

Main PCB failure

Replace the main PCB ASSY.

---

<User Check>

• Turn OFF the power switch, and turn it ON again after a while.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

Print Unable E6
Turn the power off and then back on again.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands