manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 101

2-64

Confidential

■

Error code C9, CA to CF

These errors do not usually occur in the normal use. The conceivable causes are noise around 
the installation site, fluctuation of the power supply voltage, and failures in the software.

Error, which cannot be specified, occurs.

■

Error code D1

Modem initialization failed.

■

Error code D2 to D9, DA to DC

These errors do not usually occur in the normal use. The conceivable causes are noise around 
the installation site, fluctuation of the power supply voltage, and failures in the software.

Error, which cannot be specified, occurs.

---

<User Check>

• Turn OFF the power switch, and turn it ON again after a while.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

Print Unable D1
See Troubleshooting and routine maintenance chapter in User's Guide.

<User Check>

• Turn OFF and ON the power and check if the machine recovers.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

---

<User Check>

• Turn OFF the power switch, and turn it ON again after a while.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands