manualshive.com logo in svg

Brother DCP-110C, Service Manual

Share
Download
Brother DCP-110C Service Manual Download Page 428

 App. 

4-53 

Confidential

 

WSW51 

(Function setting 16)

 

Selector 

No. 

Function 

Setting and Specifications 

1 

Output of communications error 

report when transmission 

verification report is disabled 

0:   Enable  

1:  Disable 

2 

CR motor control for reducing 

torque fluctuation 

0:   Activate  

1:  Deactivate 

3 

| 

7 

Not used. 

 

8 

Switching from ink near-empty to 

ink empty when opening the 

scanner cover 

0:   Yes  

1:  No 

   

  (No change from ink near- 

  

  

empty) 

 

  Selector 2:  CR motor control for reducing torque fluctuation 

When the CR motor runs, the motor torque may vary so as to cause the head/carriage unit travel 

velocity to fluctuate, affecting the print quality. Setting this selector to "0" activates the CR motor 

control that regulates the motor drive current to reduce torque fluctuation, running the CR motor 

smoothly. 

  Selector 8:  Switching from ink near-empty to ink empty when opening the scanner cover 

If this selector is set to "0," opening the scanner cover switches from ink near-empty (if detected) to 

ink empty state, prompting the user to replace the near-empty ink cartridge(s) immediately. 
 

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands