Brother DCP-110C Service Manual Download Page 424

Page: 424 / 466

App.

4-49

Confidential

WSW46

(Monitor of power ON/OFF state and parallel port kept at high)

Selector

No.

Function

Setting and Specifications

Monitoring the PC ON/OFF

state

(Not used.)

No. 1 2
0

Disable

0 1 : Monitor SELECT IN

Monitor

STROBE

1 1 : Monitor both SELECT IN and

STROBE

Parallel port output pins kept at

high level

(Not used.)

0: Enable

1: Disable

Previous filtering parameters for

white level compensation

(Not used.)

0: Enable

1: Disable

Not used.

NOTE:

Selector 4 is not applicable to models equipped with flat-bed scanners.

Selectors 1 and 2: Monitoring the PC ON/OFF state (Not used.)

For the related functions, refer to WSW36, selectors 2 and 3.

Selector 3: Parallel port output pins kept at high level (Not used.)

Setting this selector to "0" will keep all parallel output pins of the machine at high level. Use this

setting if Resource Manager (bundled with MFC models) installed to WindowsNT running on the

connected PC fails to monitor the power ON/OFF state of the machine.

Selector 4: Previous filtering parameters for white level compensation (Not used.)

At the start of scanning operation, the machine usually initializes white and black level data stored

in the EEPROM by scanning the while-level reference film attached to the inside of the scanner top

cover. After long use of the machine, however, the film may be contaminated with dust or dirt.

Accordingly, incorrect white level data will be set up so that white vertical streaks will be brought

on the scanning result.
Setting this selector to "0" (Enabled) will apply previously saved white level data instead of new

incorrect compensation.

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands