Brother DCP-110C Service Manual Download Page 422

Page: 422 / 466

App.

4-47

Confidential

WSW44 (

Speeding up scanning-1)

Selector

No.

Function

Setting and Specifications

Not used.

Effective time length of the

white level compensation data

obtained beforehand

(Not used.)

No. 6 7 8

0 0 0 : Obtained compensation data

ineffective

: 1

min.

: 3

min.

: 5

min.

NOTE:

Selectors 6 through 8 are applicable only to models equipped with ADF units.

Selectors 6 through 8: Effective time length of the white level compensation data obtained

beforehand (Not used.)

If you set documents in the ADF and the document front sensor detects them, the controller will

make correction of the reference voltage to be applied to white level compensation for document

scanning before the

Copy

key is pressed.

These selectors determine how long compensation data obtained beforehand will keep effective.

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands