Brother DCP-110C Service Manual Download Page 412

Page: 412 / 466

App.

4-37

Confidential

WSW34

(Function setting 12)

Selector

No.

Function

Setting and Specifications

Erasing time length of ICM

tone recorded preceding the

tone detection starting point in

the case of automatic line

disconnection due to no voice

signal received

No.

1 2 3

0 0 0 : 0

sec.

0 0 1 : 1

sec.

0 1 0 : 2

sec.

0 1 1 : 3

sec.

1 0 0 : 4

sec.

1 0 1 : 5

sec.

1 1 0 : 6

sec.

1 1 1 : 7

sec.

No. of CNG cycles to be

detected

(when the line is connected via

the external telephone in the

external TAD mode or via the

machine in F/T mode)

No. 4 5

0 0 : 0.5

(A)

0 1 : 1

(B)

1 0 : 1.5

(C)

1 1 : 2

(D)

Number of DTMF tone signals

for inhibiting the detection of

CNG during external TAD

operation

No. 6 7

0 0 : 3

0 1 : 2

1 0 : 1

1 1 : OFF

8 Not

used.

NOTE:

Selectors 1 through 5 are applicable to models equipped with built-in TADs.

Selectors 1 through 3: Erasing time length of ICM tone recorded preceding the tone detection

starting point in the case of automatic line disconnection due to no voice

signal received

If the machine has disconnected the line after detection of disconnection tone in ICM recording, it

erases tone recorded preceding the tone detection starting point for the time length set by these

selectors.

Selectors 4 and 5: No. of CNG cycles to be detected (when the line is connected via the external

telephone in the external TAD mode or via the machine in F/T mode)

The machine interprets a CNG as an effective signal if it detects a CNG signal by the number of

cycles specified by these selectors when the line is connected via the external telephone in the

external TAD mode or via the machine in F/T mode.

Selectors 6 and 7: Number of DTMF tone signals for inhibiting the detection of CNG during external

TAD operation

If the machine receives this specified number of DTMF tone signals during external TAD operation,

it will not detect CNG afterwards.
If these selectors are set to "1, 1," the CNG detection will not be inhibited.

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands