Brother DCP-110C Service Manual Download Page 404

Page: 404 / 466

App.

4-29

Confidential

WSW26

(Function setting 4)

Selector

No.

Function

Setting and Specifications

Not used.

Dialing during document

reading into the temporary

memory in in-memory message

transmission

0: Disable 1: Enable

No. of CNG cycles to be

detected

(when the line is connected via

the external telephone except in

the external TAD mode or via

the built-in telephone)

No. 4 5

0.5

(A)

1 (B)

1.5

(C)

2 (D)

No. of CNG cycles to be

detected

(when the line is connected via

the external telephone in the

external TAD mode, via the

built-in telephone in the TAD

mode, or via the machine in the

automatic reception of the F/T

mode)

No. 6 7

0 0 : 0.5

(A)

0 1 : 1

(B)

1 0 : 1.5

(C)

1 1 : 2

(D)

8 Not

used.

Selector 3: Dialing during document reading into the temporary memory in in-memory message

transmission

If this selector is set to "0," the machine waits for document reading into the memory to complete

and then starts dialing. This enables the machine to list the total number of pages in the header of

the facsimile message.

Selectors 4 and 5: No. of CNG cycles to be detected (when the line is connected via the external

telephone except in the external TAD mode or via the built-in telephone)

The machine interprets a CNG as an effective signal if it detects the CNG by the number of cycles

specified by these selectors when the line is connected via the external telephone except in the

external TAD mode or via the built-in telephone.

Selectors 6 and 7: No. of CNG cycles to be detected (when the line is connected via the external

telephone in the external TAD mode, via the built-in telephone in the TAD mode, or

via the machine in the automatic reception of the F/T mode)

The machine interprets a CNG as an effective signal if it detects the CNG by the number of cycles

specified by these selectors when the line is connected via the external telephone in the external

TAD mode, via the built-in telephone in the TAD mode, or via the machine in the automatic

reception of the F/T mode.

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands