Brother DCP-110C Service Manual Download Page 399

Page: 399 / 466

App.

4-24

Confidential

Selectors 8: Limitation on CNG detection

If this selector is set to "1," the machine detects a CNG signal according to the condition preset by

selectors 2 and 3 of WSW18 after a line is connected. If it is set to "0," the machine detects a CNG

signal as long as the line is connected.

WSW21

(TAD setting 1

)

Selector

No.

Function

Setting and Specifications

Max. waiting time for voice

signal

No. 1 2 3 4 5

0 0 0 0 0 : No

detection

0 0 0 0 1 : 1

sec.

0 0 0 1 0 : 2

sec.

0 0 0 1 1 : 3

sec.

0 1 0 0 0 : 8

sec.

1 1 1 1 1 : 31

sec.

Taping the call

No. 6 7

0 0 : Enable (signaling for U.S.A.)

0 1 : Enable (signaling for countries

except U.S.A.)

1 0 : Enable (without signaling)

Disable

Erasure of message stored in

the memory after the message

transfer

Yes 1:

NOTE:

Selectors 1 through 5 are applicable to models equipped with ICM recorders.

NOTE:

Selectors 6 and 7 are applicable to models with internal TADs.

NOTE:

Selector 8 is applicable to models equipped with TADs.

Selectors 1 through 5: Max. waiting time for voice signal

In the TAD mode, the machine waits for voice signal for the time length specified by these

selectors before it automatically shifts to the facsimile message receive mode or disconnects the

line.

Selectors 6 and 7: Taping the call

These selectors select whether or not to tape the call. Setting them to "1, 0" enables taping the call

without signaling to the calling station that the call is being taped.

Selector 8: Erasure of message stored in the memory after the message transfer

Setting this selector to "0" will erase the message recorded in the memory after the document

retrieval feature transfers the message.

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands