Brother DCP-110C Service Manual Download Page 378

Page: 378 / 466

App.

4-3

Confidential

Selector 7: Switching between pulse (DP) and tone (PB) dialing, by the function switch

This selector determines whether or not the dialing mode can be switched between the pulse (DP)

and tone (PB) dialing by using the function switch.

Selector 8: Default dialing mode, pulse (DP) or tone (PB) dialing

This selector sets the default dialing mode (pulse dialing or tone dialing) which can be changed by

the function switch. If the user switches it with the function switch when selector 7 is set to "0," the

setting specified by this selector will also be switched automatically.

WSW02

(Tone signal setting)

Selector

No.

Function

Setting and Specifications

Tone signal transmission time

length

No. 1 2

0 0 :

70 ms

0 1 :

80 ms

1 0 :

90 ms

1 : 100

Min. pause in tone dialing

No. 3 4

0 0 :

70 ms

0 1 :

80 ms

1 0 :

90 ms

1 : 140

Attenuator for pseudo ring

backtone to the line (selectable in

the range of 0-15 dB, in 1 dB

increments)

0 : 0 dB

1: 8 dB

0 : 0 dB

1: 4 dB

0 : 0 dB

1: 2 dB

0 : 0 dB

1: 1 dB

Selectors 1 through 4: Tone signal transmission time length and Min. pause in tone dialing

These selectors set the tone signal transmission time length and minimum pause in tone dialing.

(Example: If "1," "2," "3," "4," and "5" are dialed.)

Selectors 5 through 8: Attenuator for pseudo ring backtone to the line

These selectors are used to adjust the sound volume of a ring backtone in the F/T mode, an on-hold

sound, or a beep generated as a signal during remote control operation or at the start of ICM

recording.
The larger the value specified by these selectors, the greater the attenuation.

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands