manualshive.com logo in svg

Brother 9500 - HL 1660EN B/W Laser Printer, User Manual

The Brother 9500 - HL 1660EN B/W Laser Printer is an exceptional printing device that delivers sharp black and white documents with incredible speed and precision. To maximize your printer's potential, make sure to grab the free User Manual available for download at manualshive.com and unlock its full range of features and functionalities.

Share
Download
background image

CHAPTER 7 TROUBLESHOOTING

7–1

CHAPTER 7
TROUBLE SHOOTING

TROUBLESHOOTING

If any problems occur, the printer automatically stops printing, diagnoses
the problem, and displays the corresponding message to alert you. Take
the appropriate action, referring to the following tables. If you cannot
clear the problem, consult the dealer where you purchased the printer.
Inform the dealer of the message number for quick troubleshooting.

Operator Call Messages

Operator Call Message Meaning Action

CHECK XXXXXXX 

Check the paper tray.
XXXXXXX is MP TRAY/
TRAY 1/ TRAY 2.

Check the adjustment lever at
the bottom of the upper paper
cassette and adjust to the
correct setting in case of
CHECK TRAY 1.

See page 7-6.

Load a stack of paper into the
cassette.

12 COVER OPEN 

The upper cover of the printer
is open.

Close the cover.

13 JAM XXXXXX 

Paper is jammed in the
printer. XXXXXX is TRAYS/
INSIDE/ REAR/ DUPLEX.

Remove the jammed paper
from the indicated area.

See page 7-6.

14 NO CARTRIDGE 

The toner cartridge is not
installed in the printer.

Install a toner cartridge.

XX NO CASSETTE 

The paper cassette is not
installed. XX is T1/ T2.

Install the paper cassette.

16 TONER EMPTY 

The printer has almost run out
of toner: you may print
another 30 to 100 pages. (The
ALARM lamp lights at the
same time.)

Remove the toner cartridge,
rock it several times at 45°,
and install it again. Or replace
the toner cartridge with a new
one.

XX LOAD PAPER
***** SIZE

The wrong size of paper was
loaded in the paper cassette
XX. XX is MP/ T1/ T2.(The
message appears alternately to
show a particular size.)

Load the requested size of
paper in the paper cassette, or
load it on the manual feed tray
and press the FORM FEED
switch.

Summary of Contents for 9500 - HL 1660EN B/W Laser Printer



































































































































































































































































Reviews:

No comments

Related manuals for 9500 - HL 1660EN B/W Laser Printer

Qls 2000 Series Operation & Setup Manual preview
2000 Series
Brand: Qls Pages: 53
Xerox 2000 Series Operation Manual preview
2000 Series
Brand: Xerox Pages: 36
Olympus P 400 Owner'S Manual preview
P 400
Brand: Olympus Pages: 71
Panasonic Workio DP-C265 Operating Instructions Manual preview
Workio DP-C265
Brand: Panasonic Pages: 102
Oki T400 Guía De Instalación preview
T400
Brand: Oki Pages: 36
Oki T400 Installation preview
T400
Brand: Oki Pages: 3
Oki MC160MFP Network Manual preview
MC160MFP
Brand: Oki Pages: 32
Oki MB460 Setup Poster preview
MB460
Brand: Oki Pages: 2
Oki MB290 MFP Guia Do Usuário preview
MB290 MFP
Brand: Oki Pages: 96
Oki MB290 Quick Start Manual preview
MB290
Brand: Oki Pages: 2
Oki MB280 MFP User Manual preview
MB280 MFP
Brand: Oki Pages: 78
Oki MB280 Quick Start Manual preview
MB280
Brand: Oki Pages: 2
Oki MB260 MFP Wireless Usb Installation preview
MB260 MFP
Brand: Oki Pages: 2
Oki MB260 MFP Safety And Regulatory Information Manual preview
MB260 MFP
Brand: Oki Pages: 32
Oki MB260 MFP Guía Del Usuario preview
MB260 MFP
Brand: Oki Pages: 52
Oki MB260 MFP User Manual preview
MB260 MFP
Brand: Oki Pages: 49
Oki CX3641 MFP Guia De Instalação preview
CX3641 MFP
Brand: Oki Pages: 48
Oki C9850hdn Guía Del Usuario preview
C9850hdn
Brand: Oki Pages: 161

Brands by name

Popular brands

Load more brands