Brother 09055CDN Service Manual Download | Manualshive

Page: 160 / 590

background image

2-121

Confidential

■

White spots on one color image

<User Check>

- Check if the fuser fan and low-voltage power supply PCB fan are not blocked.
- Toner may be empty.  Replace the toner cartridge with a new one.
- Refer to the User’s guide and remove the dirt on the exposure drum using a cotton swab.
- The drum unit may be damaged.  Replace the drum unit with a new one.
- The belt unit may be damaged.  Replace the belt unit with a new one.

■

Pinch roller cleaning procedure

Pull out both sides of the pinch roller cover from the ribs to remove the pinch roller cover.

Clean the pinch roller with a brush as rotating the pinch roller in the arrow direction with

your fingers.

Remove paper dust accumulated in the paper tray by turning over the paper tray.

Fig. 2-18

Step

Cause

Remedy

1

Dirt on the pinch roller of the
paper tray

Refer to the figure below and clean the pinch
roller.

2

Exposure drum dirty

Refer to

"2.5 Drum Cleaning" in Chapter 5

and perform drum cleaning.

3

High-voltage power supply
PCB failure

Replace the high-voltage power supply PCB
ASSY.

4

Toner/New sensor PCB
failure

Replace the Toner/New sensor PCB ASSY.

Pinch roller cover

Paper dust

Rib

Rib

Paper tray

Pinch roller

«
...
158
159
160
161
162
...
»

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 09055CDN

Brand: F+D Feinwerk- und Drucktechnik Pages: 41

Brand: Canon Pages: 542

Brand: Ricoh Pages: 126

Genmitsu 3018-MX3

Brand: SainSmart Pages: 50

Brand: InfoPrint Pages: 170

Brand: Sagem Pages: 154

Brand: Ricoh Pages: 84

Brand: Valentin Pages: 32

4039 - B/W Laser Printer

Brand: Lexmark Pages: 49

Brand: Lexmark Pages: 64

M-Class Mark II M-4206

Brand: Datamax Pages: 76

Brand: Savin Pages: 106

Brand: Infinite Peripherals Pages: 35

Brand: Xerox Pages: 12

Brand: Toshiba Pages: 74

Brand: Toshiba Pages: 120

MX 3501N - Color Laser - Copier

Brand: Sharp Pages: 8

Brand: Sharp Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands