Brother 09055CDN Service Manual Download

Page: 125 / 590

2-86

Confidential

■

Error code BF

The document is too long for ADF duplex feeding.

<User Check>

- When you scan a document longer than the specified size (356.0 mm in length), scan the

document by dividing it into several pages using the document scanner unit.

■

Error code C0 (K)

Failure to detect a new black toner cartridge.

Error code C1 (Y)

Failure to detect a new yellow toner cartridge.

Error code C2 (M)

Failure to detect a new magenta toner cartridge.

Error code C3 (C)

Failure to detect a new cyan toner cartridge.

<User Check>

- Install the toner cartridges into the machine properly.

Scan Unable
Document is too long for duplex scanning. Press Stop Key.

Step

Cause

Remedy

Document second side rear
actuator catching on some
position

Correct catching of the document second
side rear actuator.

Main PCB failure

Replace the main PCB ASSY.

Cartridge Error
Put the Black (K) Toner Cartridge back in.

Cartridge Error

Put the Yellow (Y) Toner Cartridge back in.

Cartridge Error

Put the Magenta (M) Toner Cartridge back in.

Cartridge Error

Put the Cyan (C) Toner Cartridge back in.

Step

Cause

Remedy

Power off or front cover opened
while detecting a new toner
cartridge

Reset the developing bias voltage and
developer roller counter. (Refer to

“2.1

Developer Roller Counter Reset Function”
in Chapter 5

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands

Brother 09055CDN, Service Manual

Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands