Brother 09055CDN Service Manual Download | Manualshive

Page: 110 / 590

background image

2-71

Confidential

■

Error code 8C

Paper jam in the MP tray.

<User Check>

- Check if paper is jammed around the MP tray. If paper is jammed, remove the jammed paper.

- Check if the paper is loaded into the MP tray correctly.

- Turn back the paper loaded in the MP tray or change the orientation of the paper by 180°.

- Adjust the paper guide corresponding to the paper size.

- Check if too much paper is loaded in the tray.

- Check if the thickness of the paper is 60 to 163 g/m

2

.

■

Error code 8D

Paper jam occurred around the back cover at the time when the power was turned ON, or the
fuser cover is open.

This error does not usually occur in the normal use. The conceivable causes are noise around
the installation site, fluctuation of the power supply voltage, and failures in the software.

<User Check>

- Turn OFF the power switch, and turn it ON again after a while.

(Non Touch panel model)
Jam MP Tray
Remove the jammed paper from Multi Purpose Tray and press Start.

(Touch panel model)
Animation is displayed.

Step

Cause

Remedy

1

Foreign object around MP tray

Remove the foreign object.

2

MP paper feeding kit worn out

Replace the MP paper feeding kit.

3

MP registration front sensor
failure

Check the sensor performance following
the procedure described in

“Function code

. If any problem occurs, replace the

MP paper empty/registration front sensor
PCB ASSY.

4

Engine PCB failure

Replace the engine PCB ASSY.

5

Main PCB failure

Replace the main PCB ASSY.

Cover is Open
Make sure there is no paper jammed inside the machine and close the Back
Cover, then press Start.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

«
...
108
109
110
111
112
...
»

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 09055CDN

Brand: QMS Pages: 208

Brand: Rena Pages: 59

Brand: Citizen Pages: 32

Brand: Oki Pages: 20

Brand: Oki Pages: 105

Brand: Oki Pages: 72

Brand: Canon Pages: 48

Pixma PRO-100S series

Brand: Canon Pages: 4

Pixma PRO-100S series

Brand: Canon Pages: 2

Brand: Canon Pages: 570

Brand: Canon Pages: 571

Brand: Canon Pages: 4

Brand: Canon Pages: 769

Brand: Konica Minolta Pages: 7

imagePROGRAF iPF8300

Brand: Canon Pages: 1150

Brand: TE Connectivity Pages: 25

Brand: GeBe Pages: 4

Brand: GCC Technologies Pages: 111

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands