BRONKHORST Mini CORI-FLOW MI Series Instruction Manual Download Page 19

Page: 19 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

3.6.2.2

Software (DDE applications)

Examples of free Bronkhorst® DDE client applications: FlowPlot and FlowView. Other software programs (third party)

supporting DDE are for example MS-Office, LabVIEW, InTouch and Wizcon.

Bronkhorst® software applications 'FlowView' (left) and 'FlowPlot' (right)

FlowDDE and other Bronkhorst® applications are available on the support CD or can be downloaded from the product
pages on the Bronkhorst website:

www.bronkhorst.com/products

3.6.3

Fieldbus operation

FLOW-BUS

Digital Bronkhorst® instruments can be monitored and operated via RS232 using the free

FlowWare

software tools for

Windows. These tools provide a graphical interface to the

ProPar

protocol (used by FLOW-BUS), for monitoring and

changing instrument parameters.

The FlowWare toolkit provides functionality for monitoring and operating digital instruments (FlowPlot, FlowView) and

selection of the active fluid and configuration of the fieldbus connection (if applicable). For instruments that support the

definition and use of multiple fluids FlowTune™ can be used to define and store fluids in the instrument and select the

active fluid.

Digital instrument parameters are made accessible by

FlowDDE

, a Dynamic Data Exchange server (DDE) that handles

communication between the instrument and (dedicated) client software in Windows (e.g. FlowPlot). FlowDDE can also be

used by other client applications, such as Microsoft Office or custom made software, built with third party development

software like LabVIEW or a SCADA platform.

The FlowWare tools and associated documentation can be downloaded from the product pages on the Bronkhorst website:

www.bronkhorst.com/products

Modbus

Instruments in a Modbus system can be monitored and operated using third party software as a master device, such as

LabVIEW, ModScan, or a Modbus PLC.

Summary of Contents for Mini CORI-FLOW MI Series






















































Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual

Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands