BRONKHORST ES-FLOW ES Series Instruction Manual Download

Page: 8 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

Application

The combination of a straight sensor tube with zero dead volume, self-drainability and hygienic connections, makes the ES-

FLOW especially suitable for hygienic applications. Examples of typical use are the measuring of food ingredients like

flavourings or syrups, or measuring concentrates in CIP units. For non-hygienic applications, the instrument can be

equipped with compression type fittings. Wetted parts are made of stainless steel, the housing has a high ingress

protection rating.

Operation

The

ES-FLOW™

can be operated with the integrated readout and control unit, as well as digitally, via RS-232 or fieldbus

(Modbus, FLOW-BUS, PROFIBUS DP, PROFINET, DeviceNet™ or CANopen®), or in analog mode. The readout and control unit

has a capacitive touchscreen with a TFT display. The fluid temperature can be read out as a secondary output. An on-board

PID controller can be used to drive a control valve or pump, establishing a complete, compact control loop.

By default, the instrument is supplied with the readout and control unit above the measuring tube (assuming the flow

direction is to the right). If so required, the flow direction and display orientation can be customized to support a

convenient reading angle. The illustrations in this manual are based on the default orientation.

Multi-range

The

ES-FLOW™

offers multi-range functionality: factory calibrated ranges can be re-ranged to a different full scale range.

Because of the extremely high linearity of the sensor, this does not affect the original accuracy specifications.

The instrument comes with a calibration certificate for all supported full scale ranges. The actual full scale of the instrument

is set to a value as ordered.

1.4

Documentation

The documentation listed in the following table is available on the

ES-FLOW

product pages under

www.bronkhorst.com/products

Type

Document name

Document no.

Manuals

Instruction Manual ES-FLOW™ (this document)

9.17.145

Hook-up diagrams

Hook-up diagram Analog/RS-232

9.16.252

Hook-up diagram CANopen

9.16.250

Hook-up diagram DeviceNet™

9.16.245

Hook-up diagram FLOW-BUS

9.16.247

Hook-up diagram Modbus

9.16.246

Hook-up diagram PROFIBUS DP

9.16.248

Hook-up diagram ES-FLOW interfaces

EtherCAT / EtherNet/IP / Modbus-TCP / POWERLINK / PROFINET

9.16.251

Hook-up diagram optional bus and I/O configurations

9.16.249

Dimensional drawings

Dimensional drawing ES-103I / ES-113I

Mk I: 7.15.194

Mk II: 7.15.217

Summary of Contents for ES-FLOW ES Series
























































Search results

Summary of Contents for ES-FLOW ES Series

Reviews:

Related manuals for ES-FLOW ES Series

Brands by name

Popular brands

BRONKHORST ES-FLOW ES Series, Instruction Manual

Search results

Summary of Contents for ES-FLOW ES Series

Reviews:

Related manuals for ES-FLOW ES Series

Brands by name

Popular brands