BRONKHORST ES-FLOW ES Series Instruction Manual Download

Page: 20 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

3.3.2.3

Editing list selection

1. Select the parameter to

be edited:

2. Press to enter edit

mode (the selected

value is highlighted):

3. Press or to scroll

through the available

options:

4. Press to confirm the

selected option and

leave edit mode (the

highlight is removed):

3.3.3

Settings menu

Before the

Settings

menu can be entered, it may need to be enabled using the

Security

menu.

The

Settings

menu provides access to the user configurable instrument parameters, and contains settings for customizing

display behavior of the readout and control unit. The menu is divided into the following sections (available as sub menus):

Sub menu

Description

Readout

Readout settings and fluid selection

Controller

Instrument controller characteristics

Counter/totalizer

Counter and totalizer settings

Alarm

Alarm settings

Setup

Device identification, display customization and bus configuration

Advanced

Sensor filter settings and special functions

1. Start in the main

screen:

2. Press to enter the

Settings

menu:

3.3.3.1

Readout

Summary of Contents for ES-FLOW ES Series
























































Search results

Summary of Contents for ES-FLOW ES Series

Reviews:

Related manuals for ES-FLOW ES Series

Brands by name

Popular brands

BRONKHORST ES-FLOW ES Series, Instruction Manual

Search results

Summary of Contents for ES-FLOW ES Series

Reviews:

Related manuals for ES-FLOW ES Series

Brands by name

Popular brands